Skip to product information
1:32 AN-Mk 1 Armour Piercing 1,600lb (Set of 2).
1:32 AN-Mk 1 Armour Piercing 1,600lb (Set of 2).
1:32 AN-Mk 1 Armour Piercing 1,600lb (Set of 2).
1:32 AN-Mk 1 Armour Piercing 1,600lb (Set of 2).
1:32 AN-Mk 1 Armour Piercing 1,600lb (Set of 2).
1:32 AN-Mk 1 Armour Piercing 1,600lb (Set of 2).
1:32 AN-Mk 1 Armour Piercing 1,600lb (Set of 2).

1:32 AN-Mk 1 Armour Piercing 1,600lb (Set of 2)

$18.59 $21.69
SKU: 0172
Free Shipping on all MPM Hobbies’ 3D Printed Products
MPM Hobbies does not authorize any person, entity or establishment the right to distribute DISCOUNT CODES for use on our website. For more information, please visit our FAQs. Thank you.

3D Print Product Info

  1. High-Quality LCD-Based SLA Printed Resin Items at MPM Hobbies

  2. At MPM Hobbies, we offer a diverse range of LCD-based SLA printed resin items that are meticulously crafted using UV-cured resin. These items are shipped unpainted and come with 3D print supports attached to ensure their structural integrity during shipping.
  3. Exceptional Printing Process: To ensure the highest quality, all our items undergo a thorough cleaning process. Each item goes through a 20-minute wash cycle followed by two ten-minute sonic wash cycles. Finally, it undergoes a 2-to-8-minute curing process. This meticulous process guarantees that you receive a clean and well-prepared item ready for your creative touch.
  4. Painting and Finishing Recommendations: Our items can be easily primed with acrylic, lacquer, or enamel type paints. It is recommended to lightly sand and/or prime any horizontal striations that may be present due to the printing process. When removing the supports, it is advisable to start from the tip down and begin with the supports connected to small and fragile details. For attaching the item to your model or filling any imperfections, we recommend using CA (cyanoacrylate) adhesive.
  5. Handle with Care: Please note that some features of our items may be brittle or extremely delicate, requiring careful handling to prevent breakage. We advise that our products are not intended for small children due to the choking hazard and should only be purchased by experienced modelers who can appreciate and handle the fine details and delicate nature of these items.
  6. Accurate Representation and Configuration: Please be aware that the 3D print support configurations may differ from the ones shown in the product photos, if applicable. The product photos may include CAD rendered files used for printing to highlight intricate details that may not be easily visible in regular photos.
  7. Order Quantity and Hollow Parts: The number of items in your order is determined by multiplying the quantity you selected by the number of items per set, if applicable. Additionally, you may notice small holes on the print, which are necessary for draining any leftover resin from the hollow parts of the item. Simply fill these holes with CA adhesive and sand them for a smooth finish.
  8. Visit our website at to explore our wide range of LCD-based SLA printed resin items. We prioritize quality and provide a seamless shopping experience for hobbyists and modelers alike.
  9. For any inquiries or assistance, feel free to contact our knowledgeable team at or call 1-800-123-4567. Trust MPM Hobbies to deliver exceptional products and meet your modeling needs.
    The bodies are of single piece, forged, machined construction, with pointed noses, parallel sides, and slight boat tailing. The base plate is of the male type. Suspension in the 1,600 pound AP Bomb Mk 1 design was by means of lugs welded to bands, the bands being positioned by grooves on the external bomb surface. The newer designs, AN-Mk 1 and Mk 33, are suspended by fittings which screw into holes drilled into the bomb case and secured by bolts. The normal box-type tail assembly is used on these bombs.

    The later 1,600-pound AP Bombs Mk 1 Type were grooved to position the suspension band. Older bombs had a stud which fitted into a hole in the bomb body.

    The only fuze authorized for use with the AN-Mk 1 bomb is the AN-Mk 228 tail impact fuze.

    The difference between AN-Mk 1 Mod 1, AN-Mk 1 Mod 2, and AN-Mk 1 Mod 3 is in the manufacturer only; the complete rounds contain the same components and are the same in all physical aspects. US Bomb, 1600 lb AP, AN-Mk 1 Mod 1, 2, 3 (