Skip to product information
1:32 Mark 84 (Mk 84) 2000-pound General-Purpose Aircraft Bombs (Set of 2).
1:32 Mark 84 (Mk 84) 2000-pound General-Purpose Aircraft Bombs (Set of 2).

1:32 Mark 84 (Mk 84) 2000-pound General-Purpose Aircraft Bombs (Set of 2)

$19.39 $21.96
SKU: 0066
Free Shipping on all MPM Hobbies’ 3D Printed Products
MPM Hobbies does not authorize any person, entity or establishment the right to distribute DISCOUNT CODES for use on our website. For more information, please visit our FAQs. Thank you.

3D Print Product Info

  1. High-Quality LCD-Based SLA Printed Resin Items at MPM Hobbies

  2. At MPM Hobbies, we offer a diverse range of LCD-based SLA printed resin items that are meticulously crafted using UV-cured resin. These items are shipped unpainted and come with 3D print supports attached to ensure their structural integrity during shipping.
  3. Exceptional Printing Process: To ensure the highest quality, all our items undergo a thorough cleaning process. Each item goes through a 20-minute wash cycle followed by two ten-minute sonic wash cycles. Finally, it undergoes a 2-to-8-minute curing process. This meticulous process guarantees that you receive a clean and well-prepared item ready for your creative touch.
  4. Painting and Finishing Recommendations: Our items can be easily primed with acrylic, lacquer, or enamel type paints. It is recommended to lightly sand and/or prime any horizontal striations that may be present due to the printing process. When removing the supports, it is advisable to start from the tip down and begin with the supports connected to small and fragile details. For attaching the item to your model or filling any imperfections, we recommend using CA (cyanoacrylate) adhesive.
  5. Handle with Care: Please note that some features of our items may be brittle or extremely delicate, requiring careful handling to prevent breakage. We advise that our products are not intended for small children due to the choking hazard and should only be purchased by experienced modelers who can appreciate and handle the fine details and delicate nature of these items.
  6. Accurate Representation and Configuration: Please be aware that the 3D print support configurations may differ from the ones shown in the product photos, if applicable. The product photos may include CAD rendered files used for printing to highlight intricate details that may not be easily visible in regular photos.
  7. Order Quantity and Hollow Parts: The number of items in your order is determined by multiplying the quantity you selected by the number of items per set, if applicable. Additionally, you may notice small holes on the print, which are necessary for draining any leftover resin from the hollow parts of the item. Simply fill these holes with CA adhesive and sand them for a smooth finish.
  8. Visit our website at to explore our wide range of LCD-based SLA printed resin items. We prioritize quality and provide a seamless shopping experience for hobbyists and modelers alike.
  9. For any inquiries or assistance, feel free to contact our knowledgeable team at or call 1-800-123-4567. Trust MPM Hobbies to deliver exceptional products and meet your modeling needs.

    The 2000 lb LD Bomb Mk 84 Mod 1 has a slender body with a long, pointed nose. A conical type fin is attached to the aft end of the bomb body by eight setscrews.The bomb uses VT, mechanical, or electrical fuzes. Mechanical and VT fuzes require the installation of adapter-boosters to provide fuze seats of smaller diameters. Two conduits for an electric fuze cable harness connect the nose and tail fuze cavities with the charging receptacle cavity between the lugs on the outer surface of the bomb case. When the electric fuzes are not used, a plug is threaded into the charging receptacle cavity.

    When fuzes are not installed, the bomb body has a nose fuze plug, a base fuze plug, and a support cup in the nose fuze cavity. When the bomb is mechanically fuzed, these three parts are removed and the adapter-boosters and fuzes are inserted. The nose fuze plug and base fuze plug are replaced after electric fuzes have been installed. Adapter-boosters are not used with the electric fuzes. If the bomb is tail fuzed only, the support cup must be used in the nose fuze cavity to prevent collapse upon heavy impact.

    The bomb body has a base plug containing locking pins which are imbedded in the solidified explosive filler. Two suspension lugs spaced 30 inches apart and a hoisting lug located at the center of gravity are threaded into lug inserts on the bomb body.

    The high-explosive filler of this bomb, Tritonal 80-20, or H-6, is identified by yellow bands around the nose and conical sections of the bomb body. The base color is olive drab; identifying nomenclature is stenciled in yellow and die-stamped on one side of the bomb body.

    Bomb Mk 84 Mod 1 differs from the earlier Mod 0 bomb in that the tail fins of the Mod 1 are canted 2 degrees for added stability. US Bomb, 2000 lb GP, Mk 84 (