1/72 AGM-62 Walleye (Set of 2).
1/72 AGM-62 Walleye (Set of 2).
1/72 AGM-62 Walleye (Set of 2).
1/72 AGM-62 Walleye (Set of 2).
1/72 AGM-62 Walleye (Set of 2).
1/72 AGM-62 Walleye (Set of 2).
1/72 AGM-62 Walleye (Set of 2).
1/72 AGM-62 Walleye (Set of 2).

1/72 AGM-62 Walleye (Set of 2)

$11.49 $16.04
SKU: 0087
Free Shipping on all MPM Hobbies’ 3D Printed Products
MPM Hobbies does not authorize any person, entity or establishment the right to distribute DISCOUNT CODES for use on our website. For more information, please visit our FAQs. Thank you.

3D Print Product Info

  1. High-Quality LCD-Based SLA Printed Resin Items at MPM Hobbies

  2. At MPM Hobbies, we offer a diverse range of LCD-based SLA printed resin items that are meticulously crafted using UV-cured resin. These items are shipped unpainted and come with 3D print supports attached to ensure their structural integrity during shipping.
  3. Exceptional Printing Process: To ensure the highest quality, all our items undergo a thorough cleaning process. Each item goes through a 20-minute wash cycle followed by two ten-minute sonic wash cycles. Finally, it undergoes a 2-to-8-minute curing process. This meticulous process guarantees that you receive a clean and well-prepared item ready for your creative touch.
  4. Painting and Finishing Recommendations: Our items can be easily primed with acrylic, lacquer, or enamel type paints. It is recommended to lightly sand and/or prime any horizontal striations that may be present due to the printing process. When removing the supports, it is advisable to start from the tip down and begin with the supports connected to small and fragile details. For attaching the item to your model or filling any imperfections, we recommend using CA (cyanoacrylate) adhesive.
  5. Handle with Care: Please note that some features of our items may be brittle or extremely delicate, requiring careful handling to prevent breakage. We advise that our products are not intended for small children due to the choking hazard and should only be purchased by experienced modelers who can appreciate and handle the fine details and delicate nature of these items.
  6. Accurate Representation and Configuration: Please be aware that the 3D print support configurations may differ from the ones shown in the product photos, if applicable. The product photos may include CAD rendered files used for printing to highlight intricate details that may not be easily visible in regular photos.
  7. Order Quantity and Hollow Parts: The number of items in your order is determined by multiplying the quantity you selected by the number of items per set, if applicable. Additionally, you may notice small holes on the print, which are necessary for draining any leftover resin from the hollow parts of the item. Simply fill these holes with CA adhesive and sand them for a smooth finish.
  8. Visit our website at www.mpmhobbies.com to explore our wide range of LCD-based SLA printed resin items. We prioritize quality and provide a seamless shopping experience for hobbyists and modelers alike.
  9. For any inquiries or assistance, feel free to contact our knowledgeable team at info@mpmhobbies.com or call 1-800-123-4567. Trust MPM Hobbies to deliver exceptional products and meet your modeling needs.

    The AGM-62 Walleye is a television-guided glide bomb which was produced by Martin Marietta and used by the United States Armed Forces from the 1960s-1990s. Most had a 250 lb (113 kg) high-explosive warhead; some had a nuclear warhead. The designation of the Walleye as an "air-to-ground missile" is a misnomer, as it is an unpowered bomb with guidance avionics, similar to the more modern GBU-15. The Walleye was superseded by the AGM-65 Maverick. AGM-62 Walleye - Wikipedia